+8615280858852
+8615280858852
Safety Glove Cutting Tester also named Blade Cut Resistance Tester, is used to check the protective capability for the protective zone of the safety glove against cutting. Test principle of Blade Cut Resistance Tester Put the sample on the special test set, cutting the sample with a rotating circular blade, the blade reciprocate under a certain load and times, automatic counting and stop after tes...
Leather Lastometer Ball Burst Tester is used to test crack resistance Index of all kinds of vamp, shoe upper material and other leather surfaces. Leather Lastometer Ball Burst Tester’ test principle: fixed specimen circumference then the steel ball as a speed of 12mm/min rises upward from the inner side of the leather, when a crack occurs on the sample surface, record the height of the rise and th...
1. Always keep the Taber Abrasion Tester clean and tidy by wiping the Taber Abrasion Resistance Tester with cotton cloth. 2. The metallic surface shall be applied with anti-rust oil. 3. Fill lubricating oil for the moving parts at regular intervals. AVENO Machine Recommend: AF46 Taber Abrasion Tester Contact Us Now! Sales Dept Tel: +86 15280858852 Email: sales@avenotester.com Skyp...
Bally Leather Flexing Resistance Tester is designed for determining the flexing resistance of materials such as leather, fabric and other materials. By checking the damage degree flexing a certain time, to determine its flexibility. We have 12 and 24 test position for your choose, also you can custom made the position quantity you like. Meet Standards: SATRA TM55, ISO5402-1, ISO 17694, EN 13512, E...
What is Electronic Twist Tester? Electronic Twist Tester is special equipment used to measure the yarn twist, degree of inhomogeneity of yarns in certain lengths of cotton, wool, linen, and silk, and the twisting and shrinkage of strands, as a basis for assessing product quality and improving the production process. The test method of Electronic Twist Tester? Average untwisting slip elongation Ave...
Place the sample on the cutting board making sure that it is flat and smooth, do not stretch it. Place the cutter on the sample and release the safety catch, this is done by withdrawing the head of the catch, turning it through 90 degrees and locating the pin in the two recesses, this allows the blades to become operational. Whilst holding the cutter with one hand, apply pressure to the handle and...
Make sure that the safety catch is locked. Loosen the blade retaining screws to allow the blade retaining plates to be removed, then either turn or replace the blades. Replace the blade retaining plates and tighten the screws. Repeat this procedure for each blade. Note that blades may be rotated until all cutting corners have been used. AVENO Machine Recommend AG26 100CM2 Sample Cutter Contact Us ...
1.Installed abrasive paper (before installation, please put gloves, the fingers were not galled by sand) Get abrasive paper that length is 473 +-1mm and width is 400 mm at least. But those two items do not exceed roller, the average thickness is about 1.0 0.2 mm. Get three bars double-face tape that is equal to roller, the thickness is 0.2mm at most, the width is 50mm, add them on roller well-di...
Place the sample on the cutting board making sure that it is flat and smooth, do not stretch 100CM² Sample Cutter. Place the cutter on the sample and release the safety catch, this is done by withdrawing the head of the catch, turning it through 90 degrees and locating the pin in the two recesses, this allows the blades to become operational. Whilst holding the cutter with one hand, apply pressure...
1. Before using Low Temperature ROSS Flexing Tester, first check if there is a reliable grounding device. 2. The laboratory voltage must be stable, it is best to install a voltage regulator in the laboratory, when the voltage is unstable, do not use the test equipment, so as to avoid the phenomenon of short circuit burning circuit board due to voltage instability. 3. When replacing the test piece,...
online service
+8615280858852
sales@avenotester.com
+8615280858852
