Pneumatic Bursting Strength Tester AG10C
Pneumatic Bursting Strength Tester is used to determine the expansion force and divergence rate of fabric, woven, knitted fabrics, non-woven, paper and board.
read more+8615280858852
1. Calibration items: angle (90°), speed (60~100±5 times/min) 2. Correction equipment: angle gauge, electronic stopwatch 3. Calibration period: one year 4. Calibration steps: a) Angle correction method of Ross Flex Resistance Testing Machine: i. First adjust the machine in a horizontal state. ii. Turn the motor belt by hand or press the STOP and START keys to adjust the horizontal position of the movable end fixture, place the angle gauge on the movable fixture, and the angle gauge indication should be 0°. Continue to rotate the belt or press the STOP and START keys to move the maximum swing angle of the end fixture is 90° to observe whether it matches the value indicated by the angle gauge. b) Speed correction method of SATRA TM60 Ross Flex Tester: i. Start the POWER button on the control panel, reset the "PV" column to zero, and set the number of times in the "SV" column (the number of times that the correction speed is exceeded). ii. Press the START button to start the machine, and at the same time let the electronic stopwatch start timing. iii. When the electronic stopwatch reaches 1 minute to stop timing, press the STOP machine to stop at the same time, and observe whether the 1 minute time is consistent with the standard speed. More about ROSS Flexing Tester please click: https://www.avenotester.com/ross-flexing-tester-af23_p88.html Contact Us Now! Sales Dept Tel: +86 15280858852 Email: sales@avenotester.com Skype: sales@avenotester.com Web: www.avenotester.com
read moreStructure Of Infrared Dyeing Fastness Test Equipment: Combined with the general advantages of infrared and traditional glycerol proofer, The use of high-temperature machine door sealant, easy to use. There is a heat transfer oil insulation function in the cage, put the cup in the next time will not be lower because of the door temperature. Dye cup material: are made of high quality SUS316. Computer Of Colorfastness Dying Machine: Microcomputer control (Chinese and English LCD computer), programmable 100 kinds of technology; A temperature rise curve, temperature accuracy of up to ± 0.1 ℃, up to 20-140 ℃. Heating and cooling rate: 0.1 ℃ ~ 9.9 ℃ / min. Electric heating Of Textile Infrared Dying Equipment: Electric heating cups and cups at the same time irradiation, power, temperature difference is small, no soot pollution, no glycerin loss; and insulation, constant temperature effect, can save huge glycerol and electricity costs. More about Infrared Laboratory Dyeing Machine please click: https://www.avenotester.com/infrared-laboratory-dyeing-machine-ac19_p176.html Contact Us Now! Sales Dept Tel: +86 15280858852 Email: sales@avenotester.com Skype: sales@avenotester.com Web: www.avenotester.com
read moreApplication of Fineness Tester For Fiber Fiber Content Analyzer is mainly used for measuring various fiber diameters, cross-section analysis, and content of textile ingredients. Features of Fiber Fineness Tester Obtain the longitudinal microscopic image of the fiber through the digital camera. With the intelligent assistance of the software, the operator can quickly and conveniently realize the functions of fiber longitudinal diameter test, fiber type identification, and statistical report generation. Provides an accurate scale calibration function, which fully guarantees the accuracy of the fineness test data. Provides professional automatic image analysis and fiber diameter prompt functions, making fiber diameter testing extremely easy. Provide industry standard conversion function for non-circular cross-section fibers during longitudinal testing. The fiber fineness test results and type classification data can automatically generate professional data reports or export to EXCEL tables. Suitable for fiber diameter measurement of animal fiber, chemical fiber, cotton and linen, etc., with fast measurement speed, simple operation, and reduced human error. The fineness measurement range is 2~200μm. The fiber diameter measurement meets the requirements of the national standard GB/T 10685-1989 Wool Fiber Diameter Test Method-Projection Microscope Method. The content measurement complies with the national standard GB/T 16988-1997 for the determination of the content of the mixture of special animal fiber and wool. The measurement of cotton and linen content conforms to the textile industry standard FZ/T30003-2000, the quantitative analysis method of cotton and linen blended products, and the micro-projection method. In line with the commodity inspection standard SN/T0756-1999, the quantitative analysis method and the microscope projection method for import and export hemp/cotton blended products. Provide a library of standard samples of special animal fiber and chemical fiber, which is convenient for experimenters to compare and improve the identification ability. System composition and hardware configuration of Fiber Testing Equipment (1) System software and hardware requirements: Hardware requirements: Intel dual-core 2.0 or higher processor, 512MB or more of memory, 64MB or more of display memory, 10GB or more of hard disk space, CD-ROM drive Software requirements: Chinese Windows XP or above operating system, pre-installed EXCEL2003. The system recommends the use of 17" or more color monitors, running in 1024×768 (or higher) resolution and 24-bit true color display mode. Need to adjust the computer UAC to the minimum: win+R—input MSCONFIG—tool—change UAC settings—start—adjust to the minimum. After opening the Excel option, adjust the macro security to the lowest level to prevent the system from preventing the software from performing fiber calculations and statistics. (2) Main configuration 1) System biological microscope (including CCD) 1 set...
read more1 Before use, the heavy hammer must be installed in place, and the handwheel must be tightened and tightened. 2 When the Digital Elmendorf Tearing Tester is working, hands, heads, etc. should not be close to the handle turning area; it is strictly forbidden to make the handle touch any obstacles. 3 When the Tearing Tester has not been used for a long time, it should be oscillated several times before use, and the calibration operation should be carried out. 4 If you want to move the Fabric Tearing Testing machine, you must first place the swing device in a locked state. 5 There is no strong electromagnetic interference around. 6 The Paper Tearing Tester should be maintained regularly. More about Digital Tearing Tester please click: https://www.avenotester.com/digital-tearing-tester-ag11-3_p212.html Contact Us Now! Sales Dept Tel: +86 15280858852 Email: sales@avenotester.com Skype: sales@avenotester.com Web: www.avenotester.com
read more1. Install two uprights Locate the Fabric Appearance Meassure Board base and two uprights, and lock the screws on both sides of the base. 2. Install the lamp holder Locate the top frame with the lamp holder, and lock the screws on both sides. 3. Installation panel Locate the panel against the top of the Fabric Appearance Meassure Board, align the holes on both sides, and insert the screws. 4. Install the panel support rod Find two corresponding holes on the two uprights of the instrument frame, and install the sample support frame. More about Fabric Appearance Assessment System please click: https://www.avenotester.com/fabric-appearance-assessment-system-ag47_p261.html Contact Us Now! Sales Dept Tel: +86 15280858852 Email: sales@avenotester.com Skype: sales@avenotester.com Web: www.avenotester.com
read more1. First turn the speed knob (clockwise) to the minimum; 2. Place the object to be tested on the workbench and use a fixture to clamp it firmly; 3. Adjust the height of the upper and lower cross bars to make the distance between the clamps appropriate. 4. Adjust the "speed knob" to make the speed meet the requirements 5. Clamp the lower end of the test piece with the lower clamp, raise the lower cross bar to a proper distance and then stop the machine, and then clamp the upper part of the test piece with the upper clamp. 6. Turn on the Fabric Tensile Tester power, start the operation, adjust the experiment stroke, and stop after adjustment; 7. When everything is ready, press the up or down push-pull test to start the test. 8. When repeating the experiment, you can repeat the above operations. When you need to stop in the middle, you can press the stop switch, and you can continue after pressing the start; 9. After the test, adjust the displacement to the minimum and the speed to the minimum, and then turn off the power. More about the Universal Tensile Strength Tester please click: https://www.avenotester.com/single-column-universal-tensile-strength-tester-ag02-2_p156.html Contact Us Now! Sales Dept Tel: +86 15280858852 Email: sales@avenotester.com Skype: sales@avenotester.com Web: www.avenotester.com
read moreVacuum cleaner mode DIN Abrasion Tester is suitable to determine the wear resistance of elastic material, rubber, tires, conveyor belts, shoe soles, soft synthetic leather and other materials. Vacuum cleaner mode DIN Abrasion Tester this model with a vacuum cleaner interface can be connected to a vacuum cleaner. During test, the vacuum port will move with sample, clear the dust generated during the test, keep machines and labs clean. Do you want to know more about the vacuum cleaner mode DIN Abrasion Tester? Included Standard Accessories 2.5N weight 1pc 5N weight 1pc P60# standard abrasive paper 1pc Standard cutting die 1pc Grinding head 1pc Germany standard rubber 1pc Power line 1pc Included Option Accessories Standard rubber Vacuum cleaner More about DIN Abrasion Tester (vacuum cleaner mode) please click: https://www.avenotester.com/din-abrasion-tester-vacuum-cleaner-mode-af02b_p288.html Contact Us Now! Sales Dept Tel: +86 15280858852 Email: sales@avenotester.com Skype: sales@avenotester.com Web: www.avenotester.com
read more1. Instrument structure of Horizontal Combustibility test machine 1. Handle 9. Burner 2. Test chamber 10.Air feeder 3. Sample fixture 11.Control cabinet 4. Hammer 12.Power switch 5. Chamber door 13.Metal comb 6. Thermometer Jack 14. Flame adjusting knob 7. Fire nozzle gate 15. Dust collecting disk 8. Flame measuring rule 2. Functional Descriptiono of Horizontal Flammability Test instrument Handle: Convenient moving instrument Test chamber: The main body of the test instrument provides an independent space for the test. Chamber door: The transparent observation window facilitates observation and testing. Dust collecting disk: Collection of droplets from combustion tests Sample fixture: Sample fixing fixture Flame measuring rule: Flame height gauge. Thermometer Jack: Insert a thermometer to measure the temperature in the test box. Control cabinet: Control instrument test Burner: Flame generator Hammer: Provides tension to the marking line and triggers the timing sensor More about ASTM Horizontal Flame Tester please click: https://www.avenotester.com/horizontal-flammability-tester-ag32_p41.html Contact Us Now! Sales Dept Tel: +86 15280858852 Email: sales@avenotester.com Skype: sales@avenotester.com Web: www.avenotester.com
read more1 Overview of Water Cool Light Fastness Tester AC02 Light Fastness Tester (water-cool) is a testing machine developed by our company according to the requirements of national standards and AATCC standards. The machine adopts the latest sensor technology and microcomputer control technology, and has the advantages of high measurement and control accuracy, high intelligence, stable and reliable performance; simple and clear interface, easy operation, etc. Light Fashtness Testing Equipment complies with AATCC TM16-2003 and GB/T8427-1998, GB/T8430-1998, GB/T14576-93, GB/T15102-2006, GB/T15104-2006, ISO 105 B02 and other related requirements. It is suitable for the test of light fastness, weather fastness, light fastness and perspiration fastness to various colored textiles; it can also be used for the light fastness of paints, pigments, coatings, rubber, plastics, wood floors, paper and other materials Fastness test and light aging test. 2 Main feature of Light Fastness Test Chamber 1.2.1. Adopt 4500W long arc xenon lamp to truly simulate the sunlight spectrum; 1.2.2. High-transmittance filter combination, using 95% transmittance filter and filter tube, to achieve the same irradiance light requirements with low power consumption, making the instrument more energy-saving and environmentally friendly; 1.2.3. Standard 420nm band, irradiance digital setting, real-time monitoring, closed-loop automatic adjustment, providing the most stable irradiance test light source for different standards (340nm, 420nm, 300-400nm and 300-800nm bands are optional) ; 1.2.4. Light energy conversion technology is used to provide energy for radiometer detection and wireless transmission, without additional power supply; 1.2.5. Blackboard thermometer (BPT), standard blackboard thermometer (BST), radiometer and sample are tested at the same station (equidistant), which truly reflects the tested condition of the sample, and the measured data is synchronously transmitted by radio frequency technology; 1.2.6. Industrial temperature control (refrigeration) system, the water tank is heated to generate water vapor to control the humidification system, and quickly adjust the temperature and humidity in the test chamber to ensure that the test temperature and humidity are accurate and stable; 1.2.7. Multiple operating modes (drenching in rain, alternating light and dark), which can simulate the real climate state; 1.2.8. All sample holders can be timed separately, and different samples can be tested on the same machine, which is convenient for testing and monitoring and reduces operating costs. Running time and separate timing can be powered off to prevent accidental power off; 1.2.9, 10.1-inch large color touch screen, multiple test monitoring modes (animation, numbers, charts), easy to operate, intuitive and clear; 1.2.10. The quality guarantee that one test can run continuously for 1000 hours; 1.2.11. Industrial-grade single-chip microcomputer control, strong anti-interference abi...
read morePneumatic Bursting Strength Tester is used to determine the expansion force and divergence rate of fabric, woven, knitted fabrics, non-woven, paper and board.
read moreElectronic Laboratory Padder made of stainless steel, easy to move, especially suitable for small laboratory tests. It is mainly used for the liquid content test of small cloth samples in the process of textile printing and dyeing and after finishing, and maintain a certain uniform rolling residual rate, so that the water content is stable, and all kinds of textiles can also be soaked in water and put on the instrument to squeeze water to cooperate with the test. It is a very convenient, simple and effective test tool for the laboratory.
read moreLiquid Leak Test Needle is used to test leakage of liquid stuffed toys.
read moreThe yarn hairiness tester is used to measure and analyze the hairiness index of yarn, and automatically test and statistically analyze the length, quantity, and distribution of hairiness. Can test different kinds of yarn including short fiber yarns made from cotton, wool, linen, silk, synthetic fibers, and their blends.
read moreASTM D3985 Oxygen Gas Transmission Rate Tester suitable for measuring the oxygen permeability performance of high barrier materials such as plastic film, aluminum foil plastic film, waterproof material, metal foil, etc.
read more